Shop » 模組化合成器 » 外殼 / 電源 » Doepfer A-100LC6sw
This is an economical version of the A-100 suitcase. It is made very simple without front cover, without the metal rails and corners of the suitcase version described above. In other respects the low cost suitcase is identical to the suitcases described above (i.e. it includes the A-100 PSU2 and two bus boards).
The case is made of raw wood without laquering. The case can be varnished by the customer in any desired color e.g. by means of a spray can.
It is also available with black coating :A-100LC6V
Measures:
outside: approx. 445 x 275 x 160 mm
inside: 2 x 84 HP x 3 U (two bus boards), useable depth for A-100 modules: approx. 80 mm in the power supply area (bottom right), resp. approx. 110 mm in the remaining area (measured from inner side of the front panel until end of the pc board of the module)
Quantity of bus boards: 2
Weight (without modules): about 4 kg
Maximum Output Current:
with built-in A-100PSU2 (until about end of 2015): +12V/1200mA, -12V/1200mA
with built-in A-100PSU3 (since about early 2016): +12V/2000 mA, -12V/1200mA, +5V/4000mA
In the area near the power supply (bottom right) no modules should be assembled that are sensitive against transformer hum. We recommend to assemble only control voltage modules in this area (e.g. LFO, ADSR, trigger delay, clock divider/sequencer, sequencer, slew limiter, MIDI interfaces and so on) but no audio modules (VCO, VCF, VCA, VCP, frequency shifter, ring modulator, spring reverb and so on). Even modules width increased depth (e.g. A-113 or A-126) cannot be assembled in the power supply area. They have to be placed in a position outside the power supply area (e.g. in the upper row). But this applies only for a few modules. Normally it is no problem to arrange all modules by mounting modules with smaller depth in the power supply area.
stock article, usually available shortly
The price for the A-100 low cost suitcases can be found in the price list in the A-100 section.
Remark: The lower pictures show a black and blue varnished prototype with another type of threaded rails. The final version of the A-100 low cost case is manufactured with the same rails and threaded inserts as the standard A-100 frames and suitcases.
使用評論：
購物須知 Q&A
Q1 . 何謂鑑賞期?
依消費者保護法之規定，網路購物享有商品到貨日起算七天猶豫期。必須提醒您，「 猶豫期並非試用期 」，鑑賞期目的為提供您檢視、參考，並非提供您商品的試用，若您收到商品經檢視後有任何不合意之處，請勿拆封使用，並立即依照退貨規定辦理退貨。商品退換貨必須是完整包裝，且勿缺漏各項配件及贈品，或自行拆損原廠包裝與外盒。若有任何遺失、損毀或是缺件，可能會引響到您的退換貨權益，也可能依照損毀狀況扣除復原之相關費用。
Q2 . 如何辦理退換貨?
若您確定要辦理退貨，請務必保持商品全新完整包裝，且勿損毀原廠外盒。包含商品本體、配件、保證書、原廠包裝、附隨說明文件等，均須包含在內，勿缺漏任何一項。若有其他可歸責您的原因，造成商品損毀，將無法辦理退貨，或須將損壞費用於退款中扣抵。但商品如有新品瑕疵問題，則不在此限，享有無條件退換貨服務。
請於鑑賞期內來電或來信，詳細告知我們欲退換貨之原因、商品現況、電話，及取件的地址，我們將於 3 - 5 個工作天內安拍退貨事宜。
Q3 . 如何收到退款、需要多少時間?
依不同付款方式，退款方式與時間也不同，說明如下：
信用卡付款：帶我們收到退貨商品後約 5 至 7 個工作天，款項將會退至您信用卡帳戶。請依信用卡結帳日判斷，刷退款項可能列於本月或次月帳單，退款進程請向信用卡發卡銀行確認。
匯款：請聯絡 service [at] digilog.tw 並提供您的完整匯款資料（銀行、分行名稱、銀行代號、戶名、帳號），我們將派快遞公司前去取回您的退換貨商品，並於 5 至 7 個工作天，將款項匯還至您所指定的帳戶。
Q4 . 商品維修的運費需要自行負擔嗎?
商品維修的往返運費須自行負擔。
Waht's New
目前尚無評論