買器材 » 模組化合成器 » Clocking » Doepfer A-160-2 Clock/Trigger Divider II
Module A-160-2 is an enhanced version of the standard clock divider A-160. The module is a frequency divider for clock/trigger/gate signals, designed to be a source of lower frequencies, particularly for rhythm uses. The Clock input will take any digital signal from, eg., an LFO, MIDI sync, or the gate from a MIDI-CV interface. At the outputs, you have access to three sets of seven different sub-divided clock signals, from half the clock frequency down to 1/128. The low/high levels of the output signals are 0V and about +10V.
The A-160-2 also has a reset input. Whenever a reset signal is sensed, all outputs are set to certain levels which depend upon the selected mode.
These are the most important features of the module:
-
Three different sets of dividing factors, selected by a three-position switch at the front panel:
-
power of two: 2, 4, 8, 16, 32, 64, 128
-
prime numbers: 2, 3, 5, 7, 11, 13, 17
-
integer: 2, 3, 4, 5, 6, 7, 8
-
-
Two output modes, selected by a two-position switch at the front panel:
-
Gate mode: outputs act like the outputs of typical binary dividers
-
Trigger mode: in this mode the outputs are AND-wired with the clock signal (i.e. the clock pulsewidth affects the pulsewidth of the outputs)
-
(the center position labelled "Cst" has no meaning so far, please refer to the note at the bottom of the page)
-
-
Clock edge type selected by a jumper on the pc board:
-
positive: the rising edge of the clock signal triggers the state change of the outputs
-
negative: the falling edge of the clock signal triggers the state change of the outputs
-
-
Reset behaviour by two jumpers on the pc board:
-
level triggered: the level at the Reset input triggers the Reset
-
edge triggered: the edge of the signal at the Reset input triggers the Reset
-
positive: a high level (> 2.5V) or the rising edge at the Reset input triggers the Reset
-
negative: a low level (< 1 V) or the falling edge at the Reset input triggers the Reset
-
-
Output polarity selected by a jumper on the pc board:
-
positive: non-inverted outputs
-
negative: all seven outputs are inverted
-
使用評論：
購物須知 Q&A
Q1 . 何謂鑑賞期?
依消費者保護法之規定，網路購物享有商品到貨日起算七天猶豫期。必須提醒您，「 猶豫期並非試用期 」，鑑賞期目的為提供您檢視、參考，並非提供您商品的試用，若您收到商品經檢視後有任何不合意之處，請勿拆封使用，並立即依照退貨規定辦理退貨。商品退換貨必須是完整包裝，且勿缺漏各項配件及贈品，或自行拆損原廠包裝與外盒。若有任何遺失、損毀或是缺件，可能會引響到您的退換貨權益，也可能依照損毀狀況扣除復原之相關費用。
Q2 . 如何辦理退換貨?
若您確定要辦理退貨，請務必保持商品全新完整包裝，且勿損毀原廠外盒。包含商品本體、配件、保證書、原廠包裝、附隨說明文件等，均須包含在內，勿缺漏任何一項。若有其他可歸責您的原因，造成商品損毀，將無法辦理退貨，或須將損壞費用於退款中扣抵。但商品如有新品瑕疵問題，則不在此限，享有無條件退換貨服務。
請於鑑賞期內來電或來信，詳細告知我們欲退換貨之原因、商品現況、電話，及取件的地址，我們將於 3 - 5 個工作天內安拍退貨事宜。
Q3 . 如何收到退款、需要多少時間?
依不同付款方式，退款方式與時間也不同，說明如下：
信用卡付款：帶我們收到退貨商品後約 5 至 7 個工作天，款項將會退至您信用卡帳戶。請依信用卡結帳日判斷，刷退款項可能列於本月或次月帳單，退款進程請向信用卡發卡銀行確認。
匯款：請聯絡 service [at] digilog.tw 並提供您的完整匯款資料（銀行、分行名稱、銀行代號、戶名、帳號），我們將派快遞公司前去取回您的退換貨商品，並於 5 至 7 個工作天，將款項匯還至您所指定的帳戶。
Q4 . 商品維修的運費需要自行負擔嗎?
商品維修的往返運費須自行負擔。
最新器材
目前尚無評論